>>> DSL-520B How to configure DSL-520B to connect to Internet ?
Please note use only hard-wired network connections, to do the setting.
** Disable firewall in your PC to avoid login problem**
Step 1 Connect your PC to the LAN port of your DSL-520B
Step 2 Start up an Internet explorer and key in 192.168.1.1 (by default)
By default Username: admin Password: admin
Step 3 Click on the Quick Setup
Step 4 Uncheck the DSL Auto-connection option to configure the VPI and VCI for various countries. The value usually comes customized for local ISP. Please check with your local ISP. Key in your VPI and VCI values.
VPI and VCI value;
Singnet : VPI:0, VCI:100
Pacnet : VPI:0, VCI:100
True : VPI:0, VCI:100
TOT : VPI:1, VCI:32
TT&T : VPI:0, VCI:33
CS Loginfo : VPI:0, VCI:33
BuddyBB : VPI:0, VCI:35
Streamyx : VPI:0, VCI:35
Maxis : VPI:0, VCI:35
Jaring : VPI:0, VCI:35
further info at your area ADSL setting. (e.g. ATM PVC Configuration, Service Category, Connection Type, Encapsulation Mode)
Step 5 Select the Connection Type and click Next.
Step 6 Enter the necessary information for Username and Password.
For Singnet user your Singnet username should end with 'xxxxxx@singnet' or 'xxxxxx@singnet1500' or 'xxxxx@singnetbusiness'
For Pacific net user your username should end with 'xxxxxx@pacific.net.sg' or 'xxxxxx@pacnet1500'
For Streamyx user your username should end with 'xxxxxx@streamyx'
Username might be vary please check with your ISP for the correct username.
Step 7 Enable the WAN Service and click Next.
Step 8 Configure IP address and Subnet Mask for LAN interface and click Next.
User can use the default IP address and subnet mask.
Step 9 Check through the configuration and click Save/Reboot.
Step 10 You will see that the DSL-520B is restarting. Please allow one minute of waiting time for the restart process.
------------------------------------------------
>>> DSL-520B Basic Installation/Configuration
Web-based Configuration Utility
Connect to the Router
1.To configure the WAN connection used by the Router it is first necessary to communicate with the Router through its management interface, which is HTML-based and can be accessed using a web browser. The easiest way to make sure your computer has the correct IP settings is to configure it to use the DHCP server in the Router.
The next section describes how to change the IP configuration for a computer running a Windows operating system to be a DHCP client.
2.Type “admin” for the User Name and “admin” in the Password field. If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.
3.To access the Device Info window,
Quick Setup
1.Click the Quick Setup link on the left panel of the opening page to launch a series of setup windows.
2.Tick the DSL Auto-connect check box and then click the Next button.
If the ADSL connection is down, unselect the DSL Auto-connect checkbox and then click the Next button to manually assign VPI and VCI values.
3.This window allows you to set up ATM PVC configuration. Enter a Port Identifier, Virtual Path Identifier, and Virtual Channel Identifier. The VPI and VCI values should be provided by your ISP. This window also allows you to enable QoS by ticking the Enable Quality of Service check box. Click the Next button to continue.
4.CONNECTION TYPE
This window allows you to select the appropriate connection type. The choices include PPP over Ethernet (PPPoE), MAC Encapsulation Routing and Bridging (default).
This window also allows you to use the drop-down menu to select the desired Encapsulation Mode. Click the Next button to continue.
5.Click the PPP over Ethernet (PPPoE) radio button on this window. This window also allows you to use the drop-down menu to select the desired Encapsulation Mode. Click the Next button to continue.
6.This window allows you to set the username and the password for your PPP connection. This information is obtained from your ISP. Additional settings on this window will also depend on your ISP. Click the Next button to continue.
7.This window allows you to enable IGMP multicasting and WAN service. Click the Next button to continue.
8.This window allows you to enter an IP address and subnet mask for the LAN interface. In addition, you can either enable or disable the DHCP server.
To enable the DHCP server, enter a starting IP address, an ending IP address and a subnet mask. You may also choose to change the default value of the leased time. Click the Next button to continue.
9.This summary window allows you to confirm the settings you have just made. Click the Save/Reboot button to save your new PPP over Ethernet settings and restart the Router.
------------------------------------------------
>>> DSL-520B How to do port forwarding for the DSL-520B?
Open your computer Internet browser
Type in the address bar 192.168.1.1 Press Enter
Type in the username that is “admin” and the password is also “admin”. (If you have assigned the modem with a password, use that password.) Click OK
1. Click Advanced Settings, Click NAT, Click Add
2. Click NAT
3. Click Add
4. CKey in a Rule Name for your port forwarding rule under Custom Server.
5. Key in the IP address of the device under Server IP Address
6. Enter the ports that you want to open under External port start and end
7. Please choose the appropriate protocol type as well
8. Double check your port forwarding rules
9. Please click Save and Apply
***NOTE: This mode will appear if you’re WAN setting under PPPoE/PPPoA mode.
------------------------------------------------
>>> DSL-520B - How to configure Static IP in IPOA mode for DSL-520B (Modem + Router)
Link >> ftp://www.dlink.com.sg/DSL-520B/Updates - How to configure Static IP using IPOA on DSL-520B _Modem + Router Mode_.pdf
------------------------------------------------
